2-mark questionOutline one reason why work hardening occurs in metals during plastic deformation.2820marksEngineering · QuizMetal plasticity and yield strength2 / 8 / 20 mark questions
2-mark questionExplain one reason why the Newton-Raphson method may fail to converge to a root.2820marksEngineering · QuizNewton-Raphson method for nonlinear equations2 / 8 / 20 mark questions
2-mark questionExplain one reason why the smallest cross-section of a varying-area member is critical for failure analysis under a constant axial load.2820marksEngineering · QuizNormal stress in axially loaded bars2 / 8 / 20 mark questions
2-mark questionOutline one reason why numerical methods are used in mechanical engineering simulations.2820marksEngineering · QuizNumerical methods for engineering problems2 / 8 / 20 mark questions
2-mark questionExplain one reason why Ohm's Law cannot be applied to a diode.2820marksEngineering · QuizOhm's law and resistance in electrical circuits2 / 8 / 20 mark questions
2-mark questionExplain one reason why a hysteresis band is used in an on-off control system.2820marksEngineering · QuizOn-off feedback control and bimetallic thermostats2 / 8 / 20 mark questions
2-mark questionExplain one reason why a central heating boiler controlled solely by a timer is an example of an open-loop control system.2820marksEngineering · QuizOpen-loop control systems and feedforward control2 / 8 / 20 mark questions
2-mark questionExplain one reason why temperature control in a Plug Flow Reactor must be applied along its entire length.2820marksEngineering · QuizPI controller tuning for autoclave reactor temperature2 / 8 / 20 mark questions
2-mark questionExplain one reason why a thermocouple can be used as a temperature sensor.2820marksEngineering · QuizPID control and process instrumentation sensors2 / 8 / 20 mark questions
2-mark questionOutline one reason why the integral action in a PID controller is important for system performance.2820marksEngineering · QuizPID controller actions and Ziegler-Nichols tuning2 / 8 / 20 mark questions
2-mark questionExplain one reason why dead time reduces the effectiveness of a control system.2820marksEngineering · QuizPID controller operation and process gain2 / 8 / 20 mark questions
2-mark questionOutline one reason why integral action is used in a PID controller.2820marksEngineering · QuizPID controller tuning for process stability2 / 8 / 20 mark questions
2-mark questionExplain one reason why the Ziegler-Nichols closed-loop tuning procedure may not be suitable for all industrial processes.2820marksEngineering · QuizPID controller tuning methods and frequency response2 / 8 / 20 mark questions
2-mark questionExplain one reason why the Ziegler-Nichols method may not be suitable for all PID controller tuning applications.2820marksEngineering · QuizPID controller tuning methods and system response2 / 8 / 20 mark questions
2-mark questionExplain one reason why a closed-loop control system can become unstable.2820marksEngineering · QuizPole locations and root locus in control systems2 / 8 / 20 mark questions
2-mark questionExplain one reason why an engineer might choose a water manometer over a mercury manometer for measuring low gas pressures.2820marksEngineering · QuizPressure measurement techniques and sensor design2 / 8 / 20 mark questions
2-mark questionExplain one reason why virtual displacements must be consistent with the constraints of a system.2820marksEngineering · QuizPrinciple of virtual work in static equilibrium2 / 8 / 20 mark questions
2-mark questionExplain one reason why dead time is a challenge in process control.2820marksEngineering · QuizProcess control structures and stability2 / 8 / 20 mark questions
2-mark questionOutline one reason why feedback loops are important in control systems that use microcontrollers.2820marksEngineering · QuizProgramming microcontrollers for embedded systems2 / 8 / 20 mark questions
2-mark questionOutline one reason why the Relative Gain Array (RGA) is used in control system design.2820marksEngineering · QuizRelative gain array and model predictive control2 / 8 / 20 mark questions
2-mark questionExplain one reason why the rigid-body assumption is a simplification in engineering mechanics.2820marksEngineering · QuizRigid-body kinematics and kinetics2 / 8 / 20 mark questions
2-mark questionOutline one reason why the Routh stability method is useful for analysing system stability without fully factorising the characteristic polynomial.2820marksEngineering · QuizRouth stability criterion and root locus analysis2 / 8 / 20 mark questions
2-mark questionOutline one reason why the separation constant λ must be positive when solving the heat equation using separation of variables.2820marksEngineering · QuizSeparation of variables for the heat equation2 / 8 / 20 mark questions
2-mark questionExplain one reason why the bending moment diagram is important for the design of reinforced concrete beams.2820marksEngineering · QuizShear Force and Bending Moment Diagrams2 / 8 / 20 mark questions