Resistivity is the intrinsic property of a material that measures how strongly it opposes the flow of electric current, while resistance is the actual opposition offered by a particular object of a given shape and size.
Explain one reason why a longer wire has a greater resistance than a shorter wire of the same material and cross-sectional area.
Resistivity is the intrinsic property of a material that measures how strongly it opposes the flow of electric current, while resistance is the actual opposition offered by a particular object of a given shape and size. Also called volume resistivity or specific electrical resistance, resistivity is represented by the Greek letter rho and is measured in ohm-metres. The resistance R of a uniform conductor is directly proportional to its length l and inversely proportional to its cross-sectional area A, with resistivity as the constant of proportionality. This gives the equation R = rho l over A, which is often called Pouillet’s law after the French physicist Claude Pouillet. The same relationship can be rearranged as rho = R A over l, allowing resistivity to be calculated once the resistance and dimensions of a sample are known. Both resistance and resistivity describe how difficult it is to make current flow, but they differ in an important way: resistivity is an intensive property and does not depend on the geometry of the material, whereas resistance is an extensive property that depends on the specific object being considered.
The distinction becomes clear if you compare copper and rubber. All pure copper wires that have not been distorted in their crystalline structure have the same resistivity, no matter how long or thick they are. A long, thin copper wire has a much larger resistance than a short, thick copper wire made of the same material, simply because of its greater length and smaller cross-sectional area. Rubber, by contrast, has a far larger resistivity than copper, so a rubber rod of identical dimensions would offer vastly more resistance. A useful hydraulic analogy is to think of pushing water through a pipe. Passing current through a high-resistivity material is like pushing water through a pipe packed with sand, while passing current through a low-resistivity material is like pushing water through an empty pipe. If the pipes have the same shape and size, the sand-filled pipe resists the flow far more, but the overall resistance to flow also depends on the pipe’s dimensions: a short, wide pipe has less resistance than a narrow, long one. A convenient reference case is a solid one-metre cube of material with perfectly conducting contacts on two opposite faces: for such a cube, the measured resistance in ohms is numerically equal to the resistivity of the material in ohm-metres.
The inverse of resistivity is conductivity, usually represented by the Greek letter sigma and measured in siemens per metre. Conductivity describes how easily a material allows electric current to flow, and for a semiconductor it is given by sigma = q(n mu_n + p mu_p), where q is the electron charge, n and p are the electron and hole concentrations, and mu_n and mu_p are the electron and hole mobilities. Resistivity and conductivity are intensive properties, giving the opposition of a standard cube of material to current, whereas resistance and conductance are extensive properties, giving the opposition of a specific object. In the ideal case, the cross-section and physical composition of a material are uniform across the whole sample, and the electric field and current density are both parallel and constant everywhere. Many resistors and conducting wires satisfy this condition because they are made of a single material and have a uniform cross-section, so the simple formula R = rho l over A works well.
This equation also underpins the standard A-level required practical for finding resistivity. To determine the resistivity of a metal wire, you first measure its length with a ruler and its diameter with a micrometer or vernier callipers, taking several readings along the wire to obtain a precise average diameter. The cross-sectional area is then calculated from the diameter using the area of a circle. The wire is connected in a circuit with a power supply, an ammeter in series to measure the current, and a voltmeter in parallel to measure the potential difference across the wire. A variable resistor or potential divider is used to vary the current, and pairs of voltage and current readings are recorded. Plotting voltage on the vertical axis against current on the horizontal axis gives a straight line whose gradient is equal to the resistance of the wire. Once the resistance, length, and cross-sectional area are known, the resistivity equation can be rearranged to find rho, with units of ohm-metres. Taking multiple readings and measuring the diameter at several points improves precision and reduces the effect of random errors.
The simple linear relationship between voltage and current is only valid under certain conditions. Ohm’s law states that for a metallic conductor at constant temperature, the current is directly proportional to the voltage, so the current-voltage graph for a fixed resistor at constant temperature is a straight line through the origin. For a filament lamp, however, the filament heats up as the current increases, and its resistance rises, so the graph curves and its gradient, which is 1 over R, decreases at higher voltages. A semiconductor diode behaves even more dramatically: when reverse-biased it conducts almost no current, even at hundreds of volts, but once the forward bias exceeds roughly 0.7 volts the current increases extremely rapidly for a tiny further increase in voltage. Understanding these behaviours is essential for analysing circuits, whether you are calculating the charge flowing through a wire using Q = It, or working out the number of electrons passing a point in a given time by dividing the total charge by the elementary charge of 1.6 times 10 to the minus 19 coulombs.
Resistance also has direct real-world consequences because of the power dissipated as heat in a resistive wire. The electrical power dissipated in a resistor is given by P = V squared over R, where V is the voltage across it, so a small change in resistance can cause a significant change in heating. The Kia Battery Management System relies on Ohm’s law to monitor and regulate the flow of current within the vehicle’s high-voltage battery pack, ensuring that the battery operates safely and efficiently. In lighting systems, power dissipation must be carefully controlled; the Cooper Lighting Metalux Optimized High Bay LED Light Fixtures are designed to handle specific power levels, and if the resistance in the circuit is not correctly matched, excessive power dissipation can cause overheating, component failure, or even fire hazards, which is why such products are subject to safety recalls. There is also a remarkable special case at low temperatures: when a material is cooled below its critical temperature it can enter a superconducting state, where its resistivity drops to exactly zero. In this state a current can flow indefinitely without energy loss, and if a superconducting wire is placed in parallel with a normal conductor such as copper, the total resistance of the parallel combination becomes zero because the current takes the path of zero resistance.
In more complicated geometries, the simple resistance formula may no longer be sufficient. If the material is inhomogeneous, meaning that its resistivity varies from place to place, the exact paths of the current are not obvious and the formula R = rho l over A cannot be applied directly. This situation occurs in spreading resistance profiling, where the local relationship between current density J and electric field E must be written as a vector field equation, J of r equals sigma of r times E of r, or equivalently E of r equals rho of r times J of r. This local equation, combined with the continuity equation for charge and Poisson’s equation for the electric potential, forms a set of partial differential equations. In some special cases an exact solution can be worked out by hand, but for accurate answers in complex situations computer methods such as finite element analysis are often required.
In an exam, expect to be asked to calculate the resistance or resistivity of a wire, to rearrange the resistivity equation for length or area, to describe how to carry out the resistivity required practical, and to explain the current-voltage graphs for a fixed resistor, filament lamp, and diode. Marks are earned by converting units correctly, especially from millimetres squared to metres squared, by calculating cross-sectional area from the diameter using A = pi d squared over 4, by plotting a graph of voltage against current and using the gradient for resistance, and by stating the correct units of ohm-metres for resistivity and siemens per metre for conductivity. A strong evaluation point is that the resistivity equation assumes a uniform material at constant temperature, so for a non-ohmic component or a sample with varying composition, the simple relationship breaks down and the local or temperature-dependent behaviour must be considered.
Weigh the strengths and weaknesses of each historical model against the nanoscale counterexample to judge the equation's scope.
Steinhögl et al. (2004) found that the resistivity of copper wires increases significantly (by roughly a factor of 2) when wire widths are reduced to 50 nm, deviating from the bulk resistivity value.
The thesis assumes resistivity ρ is a fixed material property, but at nanoscale dimensions, resistivity itself becomes size-dependent, meaning R = ρl/A cannot be applied using bulk ρ values.
A strong evaluation sentence might look like: "While the equation R = ρl/A is a useful approximation for macroscopic wires, Steinhögl et al. (2004) demonstrated that for copper wires just 50 nm wide, the resistivity increases by a factor of two, showing that ρ is not a constant material property at the nanoscale and that the simple formula breaks down for modern microelectronics."
How to engineer a quantum wavefunction
Cosmological phase transitions
Finding and characterising robust quantum controls
Digital Quantum Simulation of the Spin-Boson Model under Markovian Open-System Dynamics
The Impact of Supermassive Black Holes on Milky Way and Andromeda-mass Progenitors
The Geller Equation
The Ring Nebula as a laboratory for the interaction of molecules
Approximate impedance models for sound propagation over acoustically-hard ground
The Joy of Science
How the classical world emerges from quantum physics
Unifying Neural-network Quantum States and Correlator Product States via Tensor Networks
New sensitivity of LHC measurements to composite dark matter models
Impact of Monovalent Metal Halides on the Structural and Photophysical Properties of Halide Perovskite

Smart nanomaterials for cancer diagnosis and treatment
Landauer (1952) proposed a theory for the resistivity of random binary mixtures, assuming each crystal behaves as if surrounded by a homogeneous medium with the mixture's properties. The theory showed good agreement with some experimental data but failed completely for other classes of mixtures.
▲ The study's theoretical model was not universally applicable, as it explicitly disagreed violently with a whole class of experimental mixtures, indicating a fundamental limitation in its underlying assumptions.
Read the paper →Faber and Ziman (1965) extended the simple theory of resistivity for pure liquid metals to liquid alloys, allowing for size differences between solute and solvent ions. The theory qualitatively explained why liquid solutions in polyvalent metals do not obey the familiar Nordheim and Linde rules.
▲ The study's conclusions are limited by being only qualitative explanations, with no quantitative validation or experimental data provided within the abstract itself.
Read the paper →Ziman (1961) argued that the electrical resistance of liquid monovalent metals depends on the Fourier transform of the radial distribution function, due to strong correlation between ion positions. The theory showed that resistance should be smaller than if ions scattered independently, because of coherence between diffracted waves.
▲ The study relies on simple perturbation theory, which may not accurately capture strong scattering effects or complex electron-ion interactions in real liquid metals.
Read the paper →Dai, Wong, and Lieber (1996) developed a method to measure the conductivity of individual carbon nanotubes while simultaneously imaging their structure. They found that structurally perfect nanotubes had resistivities an order of magnitude lower than previously reported, and that defects caused substantial increases in resistivity.
▲ The study's findings are limited to individual carbon nanotubes and may not generalise to bulk nanotube samples or other types of nanomaterials.
Read the paper →Matula (1979) provided recommended values for the electrical resistivity of copper, gold, palladium, and silver from cryogenic temperatures to above the melting point, corrected for thermal expansion. These recommendations were based on both theoretical considerations and experimental data from the open literature.
▲ The study's recommendations are limited by their reliance on available experimental data from the literature, which may contain inconsistencies or measurement errors that affect the accuracy of the compiled values.
Read the paper →